BEST SELLERS

Thread: M12 x 1.5 Includes: Matching Delphi plug and pins. Notes: 127 deg C (260 F) Max reading. Coolant Temp Sensor - Small Thread M12 x 1.5

Includes: Triple panel, yellow and red adjustment knobs and 3 x 12 position rotary trim modules. 12 Position Rotary Trim Module - (Boost/Fuel/Ign e...

Includes: Dual panel, yellow adjustment knob and 2 x 12 position rotary trim modules. 12 Position Rotary Trim Module - (Boost/Fuel/Ign etc) Dual Sw...

Includes: 2 position decals and matching set of Deutsch DTM 3 connectors (HT-031014) 12 Position Rotary Trim Module - (Boost/Fuel/Ign etc)

Thread: 1/8 NPT Includes: Hose fittings, rubber isolated mount and matching Set of Deutsch DTM 2 Connectors (HT-031012 Boost Control Solenoid 3 Port

Includes: Matching plug and 3 pins. 3 Bar GM MAP Sensor

Thread: 1/8 NPT Includes: Matching Delphi plug and 3 pins, -4 AN & 5mm hosetail adaptors. Notes: "TI" MAP sensors must not be mounted directly ...

Thread: 1/8 NPT Includes: Matching plug and pins, -4 AN adaptor. Notes: "TI" Pressure sensors must not be mounted directly into the fuel rail or en...

Includes: Matching male Deutsch DTM-3 Connector (HT-031001) 4 Bar Motorsport MAP Sensor

Length: 450mm (18") Suits: 1/8th NPT Thread MAP, Oil and Fuel Pressure sensors. Includes: Fragola -4 AN Hose with Male & Female 1/8th NPT Adapt...

Thread: 1/8 NPT 27TPI Includes: Matching Bosch EV1 plug & pins. Notes: 150 deg C (302 F) Max reading. Oil Temperature sensor High Range 150°C

Thread: 1/8 NPT Includes: Matching Delphi plug and 3 pins, -4 AN adaptor. Notes: "TI" Pressure sensors must not be mounted directly into the fuel r...

Size: 52mm (2") Suits: Haltech Version 2 CAN bus protocol. Includes: 52mm (2") CAN Gauge, gaugeART DTM-style CAN cable - 2.5m (8ft), mounting brack...

Thread: M18 x1.5 Includes: 1 x Weld on Bung - 303 Stainless Steel 1 x Copper washer and 1 x Blanking plug. O2 Sensor Weldable Fitting Bung and Blan...

Suits: Haltech iC-7 and Microtech ECUs Includes: 1 x HT-130049 Can Adaptor Loom Notes: Use with Microtech CAN Hub for direct plug and play CAN Adap...

Suits: Haltech iC-7 Dash, WB1, WB2 and Link Wire-in ECUs (Storm, Extreme, Fury, Thunder, Force GDI) Includes: 1 x CAN Adaptor Loom (DTM-4 to 6-pin ...

Suits: Haltech IC-7 Dash, WB1, WB2, and aftermarket ECUs using the AMP Superseal 1.0 Series Connector Includes: 1 x HT-130046 CAN Adaptor Loom (DTM...

Suits: Haltech IC-7 Dash, WBC 1, WBC 2 and Link Plug-in ECUs Includes: 1 x CAN Adaptor Loom (DTM-4 to JST 5-pin) - Suits Link PlugIn ECUs Notes: Us...

Suits: Haltech iC-7 / uC-10 Includes: 1 x HT-130053 Can Adaptor Loom CAN Adaptor Loom DTM-4 to Molex Mizu-P25 - Suits Holley Used to connect supp...

Suits: Haltech iC-7 / uC-10 Includes: 1 x HT-130052 Can Adaptor Loom Used to connect supported Haltech CAN devices to the DTM-2 CAN connector fou...

Suits: Haltech iC-7 / uC-10 Dash Includes: Cable and Fuse Haltech Dash to OBD II CAN Cable allows the Haltech iC-7 / uC-10 Dash to display the da...

Suits: iC-7/uC-10 Mounting Brackets (HT-060070 and HT-060071) Includes: 1 x Annodized Dash Tube Mount 2 x Zinc M8 x 10 Bracket Mounting Screws 4 ...

Size: 250mm x 500mm (10" x 20") Suits: Haltech uC-10 Display Dash Includes: 1 x uC-10 Moulded Panel Mount- Black Notes: Suits Haltech uC-10 Display...

Suits: uC-10 Display Dash Includes: Camera - CVBS, 720 x 480, 170 degree viewing angle, IP67 Licence plate mounting bracket 6m (19') Camera wire ha...